GhostWolf's Wood Work: Printer stand for Wolf

Copyright © T. GhostWolf Davidson.
All rights reserved. Piracy / Copyright Notice Break out of someone
else's frames here

Wolf's Printer Stand

In January of 2005, I wanted to connect my large laser jet and ink jet printers - but had no place to put them. That's when I realized that I had a fair amount of two-by-fours and plywood left over after building STella's configurable bunkbed. Voila; one printer stand!

I had already built the frame when I realized I hadn't taken any pictures; however, the dado joins were done in the same manner that I used for STella's bunkbed.

Click on the thumbnails to view details

The plywood is construction grade material, which is very strong, but also very rough. A 4x24 inch Porter Cable™ belt sander a with 80 grit belt, followed by 120 grit belt. I then cut the corners so the shelf would fit around the two-by-fours, and finished the sanding using a 1/2 pad sander. That took care of the roughness very nicely.

I used 3/8 inch plywood for the bottom shelf, as all it has to support is my paper tray. I checked the fit of the first shelf: No trimming needed, so after I took this picture, I used Gorilla Glue™ and brass wood screws to anchor the shelf.

My large format ink jet printer is rather heavy, so I used 3/4 inch plywood for the top shelf, and anchored that with Gorilla Glue and brass wood screws as well.

I completed assembly early afternoon on a Saturday. By Sunday morning, the glue had dried. I used a water-based dark walnut stain first and wiped it dry 10 minutes after applying the stain liberally. It was very sunny outside, so I let it dry for about an hour, and then applied three coats of Danish Oak oil stain at 10 minute intervals.

It was dry by the time I got off work the following Monday - so I brought it upstairs, put in in place with the laser and ink jet printers, and moved my paper tray onto the bottom shelf. If you're wondering, yes, that is a rack to the right of the stand.

Mou and I have slowly but surely been reorganizing and remodeling the house. In early October of 2005, I built a shorter CPU stand to go over the record player that is to the immediate left of the printer stand. Pictures of that stand will be posted when I complete reorganizing my workspace.

Back to Woodworking

Back to About Wolf

Last updated: Saturday, 03-Jan-2015 18:11:40 PST

Click on the thumbnails to view details
	The plywood is construction grade material, which is very strong, but also very rough. A 4x24 inch Porter Cable™ belt sander a with 80 grit belt, followed by 120 grit belt. I then cut the corners so the shelf would fit around the two-by-fours, and finished the sanding using a 1/2 pad sander. That took care of the roughness very nicely.
	I used 3/8 inch plywood for the bottom shelf, as all it has to support is my paper tray. I checked the fit of the first shelf: No trimming needed, so after I took this picture, I used Gorilla Glue™ and brass wood screws to anchor the shelf.
	My large format ink jet printer is rather heavy, so I used 3/4 inch plywood for the top shelf, and anchored that with Gorilla Glue and brass wood screws as well.
	I completed assembly early afternoon on a Saturday. By Sunday morning, the glue had dried. I used a water-based dark walnut stain first and wiped it dry 10 minutes after applying the stain liberally. It was very sunny outside, so I let it dry for about an hour, and then applied three coats of Danish Oak oil stain at 10 minute intervals. It was dry by the time I got off work the following Monday - so I brought it upstairs, put in in place with the laser and ink jet printers, and moved my paper tray onto the bottom shelf. If you're wondering, yes, that is a rack to the right of the stand.
Mou and I have slowly but surely been reorganizing and remodeling the house. In early October of 2005, I built a shorter CPU stand to go over the record player that is to the immediate left of the printer stand. Pictures of that stand will be posted when I complete reorganizing my workspace.